Easily To Pass New Network Appliance NS0-014 Dumps with 112 Questions
Latest NS0-014 Study Guides 2026 - With Test Engine PDF
NEW QUESTION # 42
Which tool is used to perform a disaster recovery simulation in an IP MetroCluster environment?
- A. MetroCluster Tiebreaker
- B. OnCommand System Manager
- C. MetroCluster Switchover Simulator
- D. ONTAP Mediator
Answer: A
NEW QUESTION # 43
What is the primary purpose of a NetApp MetroCluster solution?
- A. Disaster recovery and high availability
- B. Load balancing between storage arrays
- C. Backup management
- D. Virtual machine management
Answer: A
NEW QUESTION # 44
When expanding a MetroCluster configuration, what must be considered regarding inter-site connectivity?
- A. The number of controller nodes
- B. The number of users accessing the system
- C. Network bandwidth and latency between sites
- D. The cooling system efficiency
Answer: C
NEW QUESTION # 45
What are two key considerations when expanding a MetroCluster environment? (Select two)
- A. Ensure IP and FC switches are compatible with the new nodes
- B. Reduce the number of controller nodes for better performance
- C. Use unsupported hardware to save costs
- D. Validate ONTAP and Mediator software compatibility
Answer: A,D
NEW QUESTION # 46
Which two network configurations are supported by MetroCluster? (Select two)
- A. MPLS MetroCluster
- B. FC MetroCluster
- C. IP MetroCluster
- D. VPN MetroCluster
Answer: B,C
NEW QUESTION # 47
Which tool can you use to find out the supported switch firmware version for your planned MetroCluster installation?
- A. Hardware Universe
- B. Active IQ Unified Manager
- C. Product documentation
- D. NetApp Fusion
Answer: A
NEW QUESTION # 48
Which tool confirms compatibility between a fabric-attached MetroCluster ONTAP software release and an FC switch firmware release?
- A. ONTAP Mediator
- B. Active IQ Unified Manager
- C. MetroCluster Tiebreaker software
- D. Active IQ Config Advisor
Answer: D
NEW QUESTION # 49
When implementing a MetroCluster solution, which two configurations are required to ensure data redundancy across sites? (Select two)
- A. SyncMirror enabled for all volumes
- B. Use of Snapshot copies
- C. Single path network configuration
- D. Use of Snapshot copies
Answer: A,D
NEW QUESTION # 50
Which two tasks should be completed after expanding a MetroCluster configuration? (Select two)
- A. Test inter-site connectivity and latency
- B. Disconnect secondary sites temporarily
- C. Reinstall the Mediator software
- D. Validate SyncMirror functionality
Answer: A,D
NEW QUESTION # 51
Which two components must be validated to ensure the proper functioning of a Fibre Channel MetroCluster configuration? (Choose two)
- A. SnapMirror configuration
- B. ATTO Bridge health
- C. Mediator configuration
- D. Fibre Channel zoning
Answer: B,D
NEW QUESTION # 52
In a MetroCluster environment, which tool is used to validate the configuration before go-live?
- A. SnapMirror
- B. System Manager
- C. System Manager
- D. Config Advisor
Answer: D
NEW QUESTION # 53
What are two benefits of transitioning from an FC-based MetroCluster to an IP-based MetroCluster? (Select two)
- A. Lower hardware costs due to fewer FC components
- B. Faster sync replication
- C. Increased storage capacity
- D. Easier long-distance replication
Answer: A,D
NEW QUESTION # 54
When planning MetroCluster, what is the recommended minimum WAN bandwidth for IP communication between two sites?
- A. 10 Gbps
- B. 1 Gbps
- C. 10 Mbps
- D. 100 Mbps
Answer: B
NEW QUESTION # 55
Which two configuration steps are essential when installing MetroCluster Tiebreaker software?
(Select two)
- A. Set up IP connectivity between clusters
- B. Install ONTAP Mediator
- C. Configure cross-site LIFs
- D. Enable SyncMirror
Answer: A,C
NEW QUESTION # 56
When validating the health of a MetroCluster IP configuration, which two tools are essential for network validation? (Select two)
- A. Network troubleshooting tools (ping, traceroute)
- B. OnCommand Unified Manager
- C. NetApp Interoperability Matrix Tool (IMT)
- D. Config Advisor
Answer: A,D
NEW QUESTION # 57
Which command is used to verify the health of a MetroCluster configuration in ONTAP?
- A. metrocluster diagnostic show
- B. metrocluster show
- C. metrocluster check connectivity
- D. cluster status
Answer: B
NEW QUESTION # 58
When all nodes in a MetroCluster configuration are in a normal state, where is a node's NVRAM being mirrored to?
- A. HA partner and AUX partner
- B. DR partner and AUX partner
- C. HA partner and DR partner
- D. HA partner, DR partner and AUX partner
Answer: C
NEW QUESTION # 59
......
NS0-014 Dumps and Exam Test Engine: https://passcollection.actual4labs.com/NetworkAppliance/NS0-014-actual-exam-dumps.html